SACO lightweight " Radiation " crankshaft pulleys made in the USA, from 6061-T6 aircraft grade alloys, hard anodized finish with laser engraved timing marks available in stock size or power pulley size depending on your application Type 1 engine pulleys are a simple 2 piece design, the center hub is made from 4130 Chromoly for strength, button head hardware is full stainless steel Type 4 engine...
new Bosch 7mm premium plug wire sets for your air cooled VW Bosch is the best for all stock or mild performance air cooled engines and come with a limited lifetime warranty 7mm jacket is 100% pure silicone that is EPDM inner insulated and Kevlar reinforced with a stainless steel inner core we stock these for upright type 1 & type 3 based engines Bosch # 09001 - basically for bug, bus, karmann g...
new ISP OT Pulleys - 6 " diameter size for adequate stock fan speed/cooling machined from a solid billet T6-6061 aluminum, w/groove for stock type oil slinger ( not sand sealed ) with a BLACK hard anodized finish we made these to complement the recent boost in vintage speed engine products available in the VW aftermarket FEATURES ARE * Made from a Solid CNC T6-6010 Aluminum Alloy CNC Billet * A...
new 5 pound equalizer crank shaft pulleys available in both styles, stock oil slinger type or sand seal type made from a steel billet, much heavier then a stock pulley, to reduce crank shaft vibrations, featuring a deep belt groove pulley weight is 5 pounds damper pulleys are used to improve the crankshaft bearings & engine case lifespan pulley is balanced, black zinc plated, complete with a gl...
Jeep CJ and YJ engine parts galore. manifolds, brackets, pumps, smog crap, pans, pulleys, 1970's V-belt accessories, 1980's serpentine accessories, valve covers, heads, blocks, air cleaners. PM or call 442 327-4225
477CI Twin Turbo Methanol Engine. New Century Block, Bryant Billet Crank, Diamond Pistons, Carrillo Billet Pro Mod Rods, RFD/SME Edelbrock Victor Pro Heads, Visner Billet Intake With Pro Stock Throttle Body, Atomizer 800s, Moroso 6 Stage Dry Sump, Don Olsen Pan, Waterman 21GPM Fuel Pump, SME Billet Valve Covers. Engine has dyno pulls only 3186HP/2210TQ @ 38psi/7600RPMS. Dyno video can be seen o...
This is a great new Cylinder Head Temperature Sensor to control the air in your cylinders.This important temperature sensor will go out after so many years of usage, and will cause your interior red light to come one to check the engine. Air Temperature Sensors measure the temperature of the incoming air to the engine. This information is provided to the Engine Control Module (ECU) to determine...
I have a complete AAA Mk3 12v 2.8L VR6 swap for sale, with 5 speed manual trans. The engine and trans were originally from a '98 Jetta GLX with 90k miles on the clock, that was parted out after I pulled the engine. I was going to swap everything over to my Caddy but I am moving out of state in a few months, so the swap is now up for sale. The engine ran perfect and trans shifted smoothly throug...
I have a complete AAA Mk3 12v 2.8L VR6 swap for sale, with 5 speed manual trans. The engine and trans were originally from a '98 Jetta GLX with 90k miles on the clock, that was parted out after I pulled the engine. I was going to swap everything over to my Caddy but I am moving out of state in a few months, so the swap is now up for sale. The engine ran perfect and trans shifted smoothly throug...
new Flat 4 Fram Style F3-P oil filter kit perfect for your vintage speed equipped engine! Flat 4 has come together to put out a 100% complete kit ready to install this works with most every engine size from the 25HP/36hp to the 1600cc oil is taken from the side of the engine case and returned to the case via distributor clamp stud or gen/alt stand stud locations depending on the engine type the...
This 477ci (3.75x4.5) twin turbo engine was built and dynoed at Steve Morris Engines with top shelf parts. This combo made 3186hp/2210tq @ 38psi/7600rpms on VP M1 Methanol fuel with twin Garrett GEN2 GTX 88s. New Century aluminum block, RFD/SME Edelbrock Victor pro heads with titanium intake and super alloy exhaust valves (SME top fuel hoops), T&D steel rockers, Visner billet intake with pro st...
2003 - 2011 Saab 9-3 AERO PARTSAero side runnersDual exhaustRear bumper coverAero interior Tan and BlackDash w air bagsDoors completeTrunk w spoilerAmplifier located under drivers seatNO RIMSTurbo v-62.8 l engine blown head gasketAutomatic transmission w paddle switchesTell me what you need, i probably have it.